在淘寶購買 產品說明書 技術服務 聯系我們
一.產品特性 Key Feature
1.具有良好的穩定性、抗極壓性、防銹性和潤滑性等性能。
1. Good thermal stability, resistance to extreme pressure, anti-rust, lubricating properties and so on.
2.附于金屬表面，形成慢干的潤滑油膜，起到良好保護和潤滑作用。
2. The product adhered on the metal surface will form a slow-drying protective lubricant film, achieving good protection and lubrication.
3.耐溫區間寬，耐低溫-10℃、最佳耐溫 0～100℃，間歇耐溫 120℃。
3. Large range of temperature resistance with lowest temperature up to -10. The optimum working temperature ranges between 0～100℃ with intermittent temperature at 120 ℃.
4.產品技術成熟、質量穩定、性價比好、攜帶方便，使用簡單。
4. The product is mature in technology, stable in quality, cost-effective, portable and easy to use.
5. The product is cost effective and easy to transport/use with mature technology and stable quality.
5.本品不含有機溶劑物質，不易對皮膚造成傷害，符合環保要求。
二.使用范圍 Application
1.預組裝處理：噴于所裝配零件表面形成超薄潤滑層，不改變配合公差。如：齒輪、機械組裝、模具組裝、發電所的感應槽、蒸汽發電機等。
1. Pre-assembly process: When using spray cans, the product will form a thin lubricating coating on the surface of the assembled parts with no change in fit tolerance. The lubricant is suitable in gears, mechanical assembly, mold assembly / power generation induction groove, steam generators and so on.
2.保護薄膜：適用于裝配機件及內部潤滑，鏈條、鋼纜、螺絲、輸送帶、拉纜機、金屬鑄造機、墊圈外膜、設備的維修和保養，及高溫操作儀器、橡膠脫模和玻璃加工等。
2. Protection film: the product is applicable for internal lubrication of assembly parts, chains, wire ropes, screws, conveyor belt, pulled-cable machines, metal casting machine, washer outer membrane, machinery repair and maintenance, high-temperature operating instrument, rubber stripping, glass processing and so on.
3.潤滑性效能：用于潤滑以及保護礦業中的粗吊鉤及紡織機械的自動絡筒機、熱定型機螺桿、拉幅定型機、染色機、蒸化機、烘燥機、紡絲機、印花機、絲光機等軸承的潤滑。
3. Lubrication Effectiveness: This product can be used to lubricate and protect the mining of crude hooks and suitable for textile machinery, automatic winder, screws of heat-setting machine, stenter, dyeing/dying/spinning/printing machines, steamers, mercerizer, bearings and so on.
4.應用于開放性的轉動傳動及對偶面之間需要潤滑、減小摩擦力的場合。
4. It is applied to open rotary transmission and occasions where lubrication and friction reduction are required between dual surfaces.
5.切割工具：干性潤滑劑應用于切割刀具，可以得到最佳效益。刀具表面缺痕中所嵌二硫化鉬將使切割機切割時的效果發揮到最大。
5.Cutting Tools: dry lubricant applied to the cutting tool has shown a better effectiveness. Molybdenum disulfide applied on the marks of surface of cutting machines maximize the working efficiency.
6.塑料表層：噴涂于塑料表面更能突現產品優點，如尼龍軸承。
6. Plastic Surface: the product sprayed on the plastic surface has shown a more emergent advantage in applications such as in nylon bearings.
三.使用方法Usage method
1.使用前，先將物件表面的油污徹底清洗干凈，然后將罐身用力搖晃約 3 分鐘，以利于噴霧均勻。
1. Before use, first thoroughly clean the surface degreasing. The can is then forced to shake for about two minutes, so that the liquid will be well stirred in order to facilitate a uniform spray.
2.噴涂時，噴嘴距離工件表面約 20CM 左右，往復平行移動，勿固定在一個位置噴涂，可在工件表面長時間保持濕潤的油性潤滑膜。
2. Spray from about 20 cm to move reciprocating parallel to the workpiece and do not spray in one fixed position, so that a long-term wet and protective lubricating film is formed.
3.使用后，倒轉罐身噴射 1～2 次約 2 秒，作用為清洗噴咀，以防塞咀。
3. After use, invert cans upside down for about two seconds and spray 1-2 times in the meanwhile . The role is to clean nozzles to prevent clogging.
4.使用時應詳細閱讀產品說明書，并在專業人員指導下進行使用。
4. Users should carefully read the product manual and use under guidance of the professionals.
5.不要將本品置于兒童可觸及的位置，避免陽光暴曬或放于駕駛艙內。
5. Please do not store within the reach of children, under direct sunlight or in vehicles.
6.勿使罐液和皮膚或粘膜接觸，如有發生請用大量清水清洗并及時就醫。
6. Please prevent the direct contact with skin. If accidently splashed onto skin, please immediately rinse with flowing fresh water and approach to hospitals for medical treatment.
在淘寶購買 產品說明書 技術服務 聯系我們
|
